XPF, Elektronika, Zasilacze i przetwornice AC-DC DC-DC noty katalogowe EDW, Noty zasilacze, Elsinco, ZASILACZE, ...
[ Pobierz całość w formacie PDF ]
XPF Series
350–840 W
Dual Output DC Power Supply with Powerlex
35–60 V
• Power Factor Correction (PFC)
10–20 A
• Individual on/off switch per output
• Dual isolated outputs
115 230
• PowerFlex design with parallel or series conigu
-
ration gives variable voltage/current combina
-
tions equivalent to 6 power supplies in one unit
• Coarse and ine voltage controls
• Simultaneous display of output voltage and cur
-
rent for each output
The Xantrex XPF is a new type of bench power supply
designed to meet the need for lexibility in the choice
of voltage and current. Typically, the maximum voltage
and maximum current are not required simultaneously.
The PowerFlex design enables higher currents to be
generated at lower voltages within an overall power limit
envelope. This is achieved by using the latest switch-mode
technology.
The XPF Series are dual output DC power supplies with
two completely independent and isolated outputs. If
required, the outputs can be wired in series or parallel to
achieve up to double the maximum voltage or double the
maximum current.
PowerFlex Operating Conigurations
XPF35-10 Operating Area
XPF60-20 Operating Area
20
40
18
Each Output
Series
Parallel
35
Each Output
Series
Parallel
16
30
14
12
25
10
8
20
15
Programmable Division
Xantrex Technology Inc.
9250 Brown Deer Road
San Diego, CA 92121-2267
USA
6
4
10
2
5
0
0
0
10
20
30
40
50
60
70
0
20
40
60
80
100
120
Output Voltage
Output Voltage
858.458.0267
www.xantrex.com
sales@elgar.com
XPF Series : Product Speciications
Output : Voltage and Current
Models
35-10
60-20
Output Ratings (Each Output)
Output Voltage
0 - 35 V
0 - 60 V
Output Current
0 - 10 A
0 - 20 A
Outputs
2
2
Output Power
up to 175 W
up to 420 W (See XPF 35-10 and XPF 60-20 PowerFlex
power envelope graph)
Output
OVP Range
10% -110% of maximum output voltage
Voltage Setting
By coarse and ine controls
Current Setting
By single logarithmic control
Output Impedance
Typically <5mΩ in constant voltage mode. Typically >5kΩ in constant current mode (voltage limit at max.)
Line Regulation
<0.01% of max. output for a 10% line voltage change
Load Regulation
<0.05% of max. output for a 90% load change.
Ripple and Noise
5 mV rms max, typically 2 mV rms, <20 mV pk-pk, (20 MHz bandwidth) both outputs fully loaded (7A @ 25V), CV mode (XPF 35-10)
Typically <1mV rms, <10mV pk-pk, (20 MHz bandwidth) both outputs loaded (10A @ 42V) CV mode (XPF 60-20)
Transient Response
<2ms to within 100mV of set level (XPF 35-10) and <250μs to within 50 mV of set level (XPF 60-20) for 90% load change
Temperature Coeficient
Typically <100ppm/°C
Output Protection
Forward protection by OVP trip; maximum voltage that should be applied to the terminals is 50 V for XPF35-10 and 70V for
XPF60-20. Reverse protection by diode clap forreverse currents up to 3A.
Status Indication
LED indication of Output On, CV, CI and Power Limit. Message on display for over-voltage trip
Output Switch
Push-push switch operating electronic power control. Preset voltage and curent are displayed when the output is off
Output Terminals
4mm terminals on 19mm (0.75”) pitch. 15 A max. rating (XPF 35-10) and 30 A max. rating (XPF 60-20)
Sensing
Remote sensing via a front panel terminal block or local sensing (at output terminals). Selection by slide switch
Meter Resolution
10 mV, 10 mA
Meter Accuracy
Voltage
0.2% ± 1 digit
Current
0.5% ±1 digit
Input
AC Input
XPF35-10: 110V-120V AC or 220V-240V AC ± 10% (adjustable internally, option HV for factory set 220-240 VAC input) 50/60 Hz .
XPF60-20: 115V-240VAC ±10%, 50/60Hz. Installation Category II.
Environmental
Operating Temperature
Indoor use at altitudes up to 2000m, Pollution Degree 2
Storage Temperature
-40 °C to + 70 °C
Physical
Dimensions
Width: 8.3” (210 mm)
Height: 5.1” (130 mm)
Depth: 14.8” (375 mm)
Weight
11 lb. ( 5kg )
General
Cooling
Convection (XPF 35-10), Fan (XPF 42-20)
Power Consumption
600 VA max. (XPF 35-10), 1100 VA max. (XPF 60-20)
Safety
Complies with EN61010-1
EMC
Complies with EN61326
Warranty
3 years
Regulatory
CE-marked units meet: EN61010-1 and EN61326
Protection Features
Over voltage protection per output
Switchable remote or local sense
XPF Series
Power Envelope (each output)
The maximum current
at any voltage setting
is limited by the power
envelope which is
set to give 5A at 35V
rising to 10A at 12V
and lower.
The maximum current
at any voltage setting
is limited by the power
envelope which is
set to give 7A at 60V
rising to 20A at 20V
and lower.
10A
10A
9A
8A
7A
6A
5A
4A
3A
2A
1A
0A
XPF35-10 PowerFlex
Power Envelope
(175W max. per output)
XPF60-20 PowerFlex
Power Envelope
(420W max. per output)
15A
10A
Double the current or
double the voltage can
be achieved by parallel
or series connection of
the two outputs.
Double the current or
double the voltage can
be achieved by parallel
or series connection of
the two outputs.
5A
0A
0V
5V
10V 15V 20V 25V 30V 35V
0V
10V
20V
30V
40V
50V
60V
Model Number Description
XPF 35
10
XXX
Series
Options
Voltage
Current
Options and Accessories
HV (Input Voltage Option)
230 VAC input factory set
858.458.0267
www.xantrex.com
sales@elgar.com
[ Pobierz całość w formacie PDF ]