x-type radio operation, Motoryzacja, JAGUAR JCP
[ Pobierz całość w formacie PDF ]
Radio Operation
Radio Operation
Audio System Display Panel (in
AM/FM mode)
PTY
Priority programme type
selected
ST
Stereo
Note:
The Audio System Display panel
shown above and throughout this
handbook, displays a clock symbol and
the time in the top section. This is not
displayed on The XJ audio system.
16
Radio Operation
Radio Operation
On/Off and volume control
Reception
FM reception offers the advantages of low
noise interference, minimal distortion,
wide dynamic range, extended frequency
response, and is usually broadcast in
stereo. FM frequency waves are however
relatively short and travel in a straight line
and can therefore be impeded by
obstructions, which may adversely affect
reception in certain parts of the country.
This is a condition known as Multipath
Interference.
Whilst FM reception generally provides
better quality sound, AM reception may
prove superior in remote areas not
covered by the shorter range FM
transmitters.
When experiencing poor FM reception,
background noise can be reduced by
pressing the
MODE
button, selecting
TREBLE
and reducing the treble setting.
Press the control knob to switch the radio
on, press again to switch off. Turn the
control knob clockwise to increase or
counter clockwise to decrease volume.
Any volume setting made whilst in audio,
phone, or voice activation mode, will be
memorised for that system.
Automatic volume control (AVC)
This maintains radio volume at a level
sufficient to overcome road noise as
vehicle speed increases or decreases. To
activate AVC, press and hold the volume
control knob until
AVC
is displayed. To
deactivate AVC, momentarily press the
volume control knob again. The level of
AVC control can be adjusted by turning
the volume control knob whilst in
AVC ON
mode. When AVC is ON, manual
adjustment of volume will override the
AVC setting.
17
Radio Operation
MODE button
The
MODE
button functions at
two levels and is primarily used to
adjust sound quality to personal
preference. In addition, it is used to adjust
Voice Activation volume, select Voice
Activation Training and to set the audio
display clock on the S-TYPE and X-TYPE.
It can also inhibit the rear multimedia
system controls on The XJ.
Digital signal processing (DSP)
(Premium audio system only)
DSP facilitates optimisation of sound for
specific seating positions. To optimise
sound for all seating positions:
•
Repeatedly press the
MODE
button
until
POS ALL
is displayed.
•
Rotate the volume control knob to
cycle through
POS F-LEFT
(front left),
POS F-RIGHT
(front right),
POS REAR
and
POS FRONT
until the
desired setting is achieved.
Following approximately five seconds of
no further actions or adjustments, the
audio system will return to the previous
display.
Note:
To improve the comfort of
passengers in the rear of the vehicle, the
bass performance of the subwoofer is
reduced when DSP mode is set to
POS ALL
or
POS REAR
.
For optimum bass performance it is
recommended that the DSP mode is set
to
POS FRONT
,
POS F-RIGHT
or
POS F-LEFT
.
Mode level 1
Repeatedly press and release the
MODE
button to scroll through the following
modes:
BASS
Increase/decrease
TREBLE
Increase/decrease
BALANCE
Left to right
FADE
Front to rear
SUB LEVEL (Premium audio
system only)
Increase/decrease
subwoofers
With a mode selected, adjust the volume
control knob to the desired level. After
approximately five seconds the audio
system will return to normal volume
control mode.
18
Radio Operation
Mode level 2
(S-TYPE and X-TYPE)
Press and hold the
MODE
button until
TA VOLUME
is displayed, then
repeatedly press and release to scroll to
the following displays as required:
•
VOICE
(adjust Voice Activation
volume).
•
VOICE TRAIN A
.
•
VOICE TRAIN B
.
•
CLOCK SET
.
Press and hold the
MODE
button to exit.
(The XJ only)
Press and hold the
MODE
button until
RMS LOCK / RMS UNLOCK /
RMS H/PHONE
is displayed (if Rear
Multimedia System (RMS) is fitted), then
repeatedly press and release to scroll to
the following displays as required:
•
RMS ON / RMS H/PHONE /
RMS OFF
(adjust with rotary volume
control).
•
RMSREARSPKRON:
RMSREARSPKROFF
(adjust with
rotary volume control).
•
TA VOLUME
(adjust with rotary
volume control).
•
VOICE VOLUME
(adjust with rotary
volume control).
•
VOICE TRAIN A
(press seek up to
adjust).
•
VOICE TRAIN B
(press seek up to
adjust).
Press and hold
MODE
button to exit.
Rear multimedia system settings
(The XJ only)
!
WARNING:
With the multimedia system turned on,
the rear seat passengers have the
ability to control the audio system
functions including the adjustment of
volume through the cabin speakers.
To inhibit the Rear Multimedia System
Controls press and hold the
MODE
button until the current
RMS MODE
is
displayed. The displays available are
RMS OFF
,
RMS ON
or
RMS H/PHONE
.
Rotate the volume knob one position to
the left or right to change the system
mode as required:
•
RMS ON
– This resets the rear switch
pack controls.
•
RMS H/PHONE
– The rear switch
pack control of cabin speakers is
inhibited. Control using headphones
is still available.
•
RMS OFF
– This fully inhibits the rear
switch pack controls.
19
Radio Operation
Setting the audio display clock
(S-TYPE and X-TYPE)
•
Change audio system source
Press and hold the
MODE
button until
TA VOLUME
is displayed.
•
Repeatedly press and release the
MODE
button until
CLOCK SET
is
displayed.
•
While the hour format is flashing, use
the seek up/seek down keys to select
either 12 or 24 hour format.
Press the desired audio system source
button.
•
Press and release the
MODE
button.
•
If the 12 hour format has been
selected, use the # key to select
AM
or
PM
as appropriate.
Source tone memory
Bass and Treble positions are
automatically memorised for AM radio,
FM radio, cassette tape and CD/MD,
allowing individual settings for each
mode.
•
Using the keypad, enter the correct
time. It should be noted that the clock
time must be entered as
four digits
e.g.
0325
or
1525
, when in 12 or
24 hour format.
Band switch AM/FM
Pressing
AM/FM
repeatedly will cycle the
radio through FM wavebands. Band
selection will be shown in the display
panel. When a tape or CD is being played,
pressing the band switch will select radio
operation.
•
To exit the clock setting procedure,
press and hold the
MODE
button until
the display reverts to audio mode.
20
[ Pobierz całość w formacie PDF ]